Powermate 010-0029CT Manuel d'utilisation et d'entretien télécharger pdf (Page 3)

3 - ENG

PERSONAL SAFETY (continued)

RISK OF HEARING LOSS. Always wear ANSI S3.19 approved ear protection when using

the tool. Prolonged exposure to high intensity noise is able to cause hearing loss.

RISK OF EYE INJURY. Always wear ANSI Z87.1 approved safety goggles when using an

air tool. Air powered equipment and power tools are capable of propelling materials such as

metal chips, sawdust, and other debris at high speed which could result in serious eye injury.

RISK OF INJURY. Do not overreach. Keep proper footing and balance at all times. Proper

footing and balance enables better control of the tool in unexpected situations.

RISK OF INJURY. Avoid prolonged exposure to vibration. Air powered tools can vibrate

during use and repetitive motion or vibration may cause injury. Avoid prolonged use of the tool

or stop using the tool if discomfort occurs.

TOOL USE AND CARE SAFETY

RISK OF INJURY. Do not use the tool if the trigger does not turn the tool on or off. Any

tool that cannot be controlled with the trigger is dangerous and must be repaired.

RISK OF INJURY. Disconnect the tool from the air source before making any adjust-

ments, changing accessories, cleaning or storing the tool.

RISK OF INJURY. Store the tool when it is idle, out of reach of children and other

untrained persons. A tool is dangerous in the hands of untrained users.

RISK OF BURSTING AND/OR INJURY. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that affects the tool's operation. If

damaged, have the tool serviced before using. Do not operate the tool with the protective

guarding removed or damaged. Replace the tool or have it repaired by an authorized service

center. Many accidents are caused by poorly maintained tools or air hose. There is a risk of

bursting if the tool is damaged.

RISK OF BURSTING AND/OR INJURY. Check for damaged air hose. Keep the air hose

away from heat, oil, and sharp edges. Inspect the air hose periodically and replace it if it

becomes worn or damaged.

RISK OF EXPLOSION AND/OR INJURY. Use compressed air regulated to a maximum

pressure at or below the rated pressure of any attachments. This spray gun is designed

to operate best at pressures between 30-60 PSI. Never attempt to operate the spray gun at

pressures in excess of 60 PSI. Exceeding the maximum pressure rating of tools or acces-

sories could cause an explosion resulting in serious injury.

RISK OF EXPLOSION AND/OR INJURY. Halogenated hydrocarbon solvents—for example:

1,1,1- trichlorethane and methylene chloride—can chemically react with aluminum used in

most spray equipment and can cause an explosion hazard. Read the label or data sheet for

the material you intend to spray. DO NOT use spray materials containing these solvents.

RISK OF INJURY. Use only accessories that are designed for the specific tool. Use of an

accessory not intended for use with the specific tool, increases the risk of injury to persons.

TOOL SERVICE SAFETY

RISK OF INJURY. Tool service must be performed only by qualified repair personnel.

RISK OF INJURY. When servicing a tool, use only identical replacement parts. Use only

authorized parts.

AIR SOURCE SAFETY

RISK OF BURSTING AND/OR INJURY. Never connect to an air source that is greater

than 60 psi. Over pressurizing the tool is able to result in bursting, abnormal operation,

breakage of the tool, or serious injury to persons. Use only clean, dry, regulated compressed

air at the rated pressure or within the rated pressure range as marked on the tool. Always ver-

ify prior to using the tool that the air source has been adjusted to the rated air pressure or

within the rated air pressure range.

RISK OF EXPLOSION AND INJURY. Never use oxygen, carbon dioxide, combustible

gases or any bottled gas as an air source for the tool. Such gases are capable of explo-

sion and serious injury to persons.

1 2 3 4 5 6 7 8 ... 19 20

Commentaires sur ces manuels

Pas de commentaire

Powermate 010-0029CT Manuel d'utilisation et d'entretien Page 3

Commentaires sur ces manuels